Temporary power, generators and site services across Kern CountyOpen daily, 7am-7pm

Job Site Power ยท Bakersfield, CA

Temporary Power Pole Installation

Temp service poles with meter base, panel and GFCI outlets, built and inspected for PG&E or SCE hookup. Call (661) 605-6031 for a free estimate.

Get Rates: Temporary Power Pole Installation

We call back during business hours, 7am to 7pm, seven days a week.

Utility pole top with a service drop and weatherhead against a blue sky over a Bakersfield site

Temp Service Poles for Kern County Builders

A temporary power pole is the cheapest way to run a construction site that is going to be active for more than a few weeks. Once it is energized, the crew pays utility rates for the power it uses, with no fuel deliveries and no generator noise on a lot surrounded by occupied homes. We build temp poles for single lots in Seven Oaks, phased tracts in Rosedale and northwest Bakersfield, commercial pads along Coffee Road and Stockdale Highway, and ag buildings out on the county roads.

A standard build is a treated wood pole or a steel post set to depth, a utility approved meter socket, a main breaker and a small distribution panel with GFCI receptacles, plus ground rods and the conductor to bond them. Overhead services get a weatherhead and enough height for the drop to clear the driveway. Underground services get conduit run to the utility pedestal or transformer. Larger jobs often need 200 amp or 400 amp service, three phase for tower cranes and welders, or more than one pole spread across a big site.

We pull the electrical permit with the right building office, schedule the inspection, and file the paperwork the utility needs to energize. Once your permanent meter is set, our crew comes back for the temp pole, backfills the hole and leaves the lot clean. Temp poles are where Bakersfield Temporary Power started, and they are still most of what our electricians build.

Built to Pass the First Inspection

A failed temp inspection costs more than a fee. It sends the job back into the inspector's queue and then into the utility's energize queue, and on a busy subdivision that delay can stretch out. We build every pole to the serving utility's current service requirements and to the code the local building department enforces, and we check the details inspectors flag most: pole depth and plumb, burial depth on underground runs, ground rod spacing, meter height, GFCI protection and a proper bonding jumper.

Our electricians have worked with the City of Bakersfield Building Division, Kern County Public Works and the smaller city departments in Delano, Shafter, Wasco and Tehachapi. They know what each office expects to see on site. If the job is in a tract with power on the far side of the street, we can plan the pole location with the builder so the drop is short and the service comes off the right transformer. When the pole has to wait on the utility, a Diesel Generator Rental keeps the trades working in the gap.

Why Valley Builders Run Temp Service

Most builders in Bakersfield go straight to a temp pole once they have a lot and a permit. These are the reasons we hear most often from supers and owners who are weighing a pole against a generator.

Lower cost on long builds

A house or commercial building that takes four to nine months to frame and finish will burn a lot of diesel on a generator. Utility power through a temp meter is usually much cheaper per month once the setup cost is paid, and nobody has to schedule fuel runs.

Quiet power near occupied homes

Infill lots and later phases of a tract sit right beside people who already live there. A pole makes no noise and no exhaust, which keeps the neighbors calmer and the city code enforcement office out of your inbox.

Steady voltage for tools and chargers

Saws, compressors, battery chargers and the office trailer all run better on utility power than on a generator that is close to its limit. Clean voltage also helps the low voltage contractor test equipment before move-in.

A place to hang lights and cameras

Once the site has a temp panel, you can plug in site lighting, a Camera Trailer Rental unit or a construction office without bringing another generator. One pole can carry most of the small loads on a residential job.

From Address to Energized Meter

  1. Site address and load review

    Send the address, the APN if you have it, and a list of what has to run. We confirm the serving utility, the building office and the amperage and phase the job needs, then send a written quote.

  2. Permit and utility application

    We pull the electrical permit for the temp service and start the utility's application for a temporary connection. If the job needs a new service point or transformer work, the utility will tell us, and we tell you right away.

  3. Pole set and wiring

    Our crew sets the pole or post, mounts the meter socket and panel, installs the breakers and receptacles, drives the ground rods and runs conduit for underground jobs. We call 811 before we dig.

  4. Inspection and release

    The building inspector checks the pole and the wiring. Once it passes, the office releases the service to the utility so it can be energized.

  5. Energize, then removal

    The utility connects the drop or the underground lateral and sets the meter. When your permanent service is live, call us and we pull the temp pole, backfill and clean up the spot.

Pole Options for Kern County Jobs

Overhead drop or underground feed

Older parts of Bakersfield and many county roads still have overhead lines, so the pole takes a drop from the nearest utility pole. Newer subdivisions in the southwest and northwest are mostly underground, and the temp service feeds from a pedestal or pad-mounted transformer through buried conduit.

Single phase and three phase service

A house build runs fine on 100 or 200 amp single phase. Tilt-up warehouses, ag processing buildings and jobs with a tower crane, large welders or a big concrete pump often need three phase. Three phase availability depends on what the utility has near the site, so we check early.

Multiple poles on large sites

Tracts, schools and solar substations can be too big for one service. We place poles where the work is concentrated and add a Tower Light Rental plan for areas the poles cannot reach, so nobody runs a 300 foot cord across the pad.

Temporary Power Pole Installation: Superintendent Questions

Do I need a permit for a temp pole in Bakersfield?

Yes. Temporary electrical service needs a permit and an inspection before the utility will connect it. Inside city limits that goes through the City of Bakersfield Development Services Building Division. Unincorporated areas like Oildale, Lamont and Rosedale go through Kern County Public Works. We pull it for you.

How long does PG&E take to energize a temp pole?

It varies with the season, the workload in your area and whether the site already has a service point nearby. A simple hookup can be quick, while a job that needs new utility equipment takes longer. Apply as early as you can, and we will keep you updated as the request moves along.

Can the same temp pole stay up for the whole build?

Usually it can, as long as it stays where the grading and the foundation work will not hit it. We help you pick a spot near the street or the utility pedestal that will not be in the way of the concrete trucks or the driveway approach.

What size temp service does a commercial job in Kern County need?

Small commercial and tenant improvements often run on 200 amps. Tilt-up buildings, schools and ag plants usually need 400 amps or more, and three phase if the job has cranes or heavy welders. We work it out from your equipment list.

More site equipment

  • Site Internet Service

    Cellular and satellite internet for job trailers, cameras and gate systems on sites with no wired service.

  • Camera Trailer Rental

    Mobile surveillance trailers with cameras, lights and alerts to protect copper, tools and equipment overnight.

  • Diesel Generator Rental

    Towable and skid diesel generators sized for valley heat, with fuel delivery and service included in the plan.

  • Tower Light Rental

    Diesel and LED light towers for night pours, shutdowns, harvest shifts and foggy winter mornings on the valley floor.

  • Industrial Spot Cooling

    Portable spot coolers and ducted air for warehouses, plant rooms and crews working through valley heat.

Pole, generator, lights or cooling on the next job? Send the address and the load. We will price it today.

Call (661) 605-6031